Car Codes diagnostic trouble code
…ate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: FC 2D9B Knock Sensor, Signal While performing test plan B1214 M KNOCK SENSOR, the following error message will be displayed: ""An error has occurred during execution of a service program. Fault code: 61/3."" This error in the test plan will not allow diagnosis to continue. The test plan error will be repaired with ISTA/…
Code interpretation
What B1214 means
This code indicates Vehicle fault code with verified manufacturer evidence Its precise meaning depends on the reporting control module, complete failure-type suffix, model year, powertrain and software level.
Driver experience
Symptoms you may notice
A stored diagnostic trouble code or a related system warning.
Test, do not guess
Possible causes
The precise cause depends on the reporting module, vehicle specification, circuit condition and software level.
Evidence-led checks
Recommended diagnostic route
Save the complete scan and confirm the code against model-specific technical information before testing.
- Capture the evidenceSave the complete all-module scan, code suffixes and freeze-frame data.
- Prove the basicsTest battery condition, system voltage, power and grounds.
- Identify the reporterConfirm the module that logged the code and check circuit integrity.
- Compare live dataReview commanded and actual values under the conditions that set the code.
- Test before replacingUse model-specific wiring diagrams, pin tests and technical information.
- Verify the repairClear the code only after recording evidence, then confirm it does not return.
Vehicle fitment
Vehicle applicability
MINI Cooper Electric, MINI Cooper Convertible, BMW 1 Series, BMW M5 Touring, BMW X5, BMW X5 M, BMW X6, BMW X6 M
Before clearing
Can the code be cleared?
Clearing a code without fixing the cause removes useful evidence and may only switch the warning off temporarily. Save the full scan first; a permanent or repeatedly returning code needs testing.
Confirm the suffix, reporting module, model, year, engine and live data before replacing a component.
Verified public evidence
Manufacturer and model coverage
59 public manufacturer records match this search. These records support applicability research but do not replace VIN-specific workshop information.
1 SERIES M · 2011 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
Source1 SERIES M · 2012 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
Source1 SERIES M · 2013 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceM5 · 2013 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2007 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2008 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2009 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2010 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2011 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2012 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 · 2013 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 M · 2010 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 M · 2011 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX5 M · 2012 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX6 · 2008 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX6 · 2009 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX6 · 2010 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX6 · 2011 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX6 · 2012 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
SourceX6 · 2013 · Multiple/unspecified
…with one of the following test plans and ISTA/D 2.33, an error will be encountered in the display. The value of the low-pressure fuel supply sensor will read 0 bar…
Source